Cold Spray Hand-push Airless Road painting machine is widely used for marking restrictive signs of different guidelines and warnings on the highway, parking, square, runway, and other flat roads. Advantages: High speed, high performance, innovative tech, proven quality.

If you are looking for Cold paint cold plastic airless pavement marking machine for sale, please leave a message.

Hand-push high-pressure airless cooling spray marking machine

Cold Spray Road Painting Machine

Because the paint does not require compressed air atomization, it is called airless spray. Cold paint Road Painting Machine uses a high-pressure equal flow type airless sprayer. This line marking machine is driven by a Honda engine to form a high pressure for spraying. The spray gun uses a rod lifting design, and accurate and convenient spray width adjustment making the line evenly thick and uniform. This series of Road marking equipment for sale is suitable for road marking, runway routes, garage marking, and so on. Now contact us to get a cheap road painting machine factory price. WhatsApp/Tel 008613598866720.

Parameter of Road Painting Machine:

ModelYG-6LYG-8L
Engine Power4.3HP7HP
Unloading Flow6L/min8L/min
Max Output Pressure25mpa30mpa
High-Pressure Pipe Strength35mpa40mpa
High-Pressure Pipe Lengthφ6*10mφ6*2 φ10*10m
Max Spray Width20cm45cm
Dimension1270mm*430mm*650mm1400mm*850mm*1050mm
Net Weight72kg130kg

Features of Line Painting Machine:

  1. High efficiency: spraying efficiency is up to 200-500㎡/h, which is more than 10 times that of the drive roller.
  2. High quality: sprayed layer is smooth, and dense, with no brush marks, roll marks, or particles.
  3. Long-life for use: high-pressure airless spray enables the paint particles to penetrate into the voids of the road. So the paint film and road surface form a mechanical bite, enhance the paint adhesion, and prolong the service life.
  4. It is easy to paint corners, voids, and uneven brushing areas.
  5. Save paint: the coating utilization rate is high. And it is easy to obtain a thickness of 30um coating for airless spraying, which can save 20-30% of the coating.

Structure of Road Painting Machine:

Road Painting Machine consists of frame, gasoline engine, the main body of pump body, suction and gas valve, pressure regulator valve, high-pressure hose, spray gun, suction mounting, and gun mounting, etc. Send your requirement to us if you need to buy road painting machine.

Hand-push Cold Spray Road Marking Machine:

ModelYG-8SYG-8D
Power5.5HP5.5HP
Plunger PumpElectronic CommutationAutomatic Reciprocating Reversion
Spray Gun QuantitySingle GunTwo Guns
Operation ModeHydraulic DriveHydraulic Drive
Work Pressure8-12MPa8-12MPa
Flow Of Spray4.8L/min8L/min
Width Of Spray100-300mm100-450mm
Thickness Of Spray0.2-0.4mm0.2-0.4mm
Dimension1600mm*800mm*1200mm1600mm*800mm*1200mm
Weight120kg120kg

Vehicular Scribing Machine

An airless spray marking machine pressurizes the paint to 3000PSK 210Kg/cm by a high-pressure plunger pump, the high-pressure paint is delivered to the spray gun through the high-pressure hose, and the pressure is released through the nozzle to form a spray, thereby forming a dense coating on the wall surface. Click here you can check our road painting machine for sale.

Parameter:

ModelYG-9HPYG-13HP
Power9HP13HP
Spray Gun QuantityTwo Guns
Drive ModeTruck-mounted
Work Pressure10-18MPa10-18MPa
Flow Of Spray20L/min*220L/min
Width Of Spray100-450mm100-450mm(single gun)
Thickness Of Spray0.2-0.4mm0.2-0.4mm
Dimension1150mm*1050mm*1300mm1530mm*1230mm*1380mm
Weight200kg600kg

What Should We Do Before Road Painting Machine Working?

  1. The paint to be sprayed must be filtered through a 60-mesh screen;
  2. Install the high-pressure hose, spray gun, nozzle, suction tube, and so on.
  3. Check the connection of every part in the high-pressure system.
Road Line Painting Machine

Test Step Before Spraying:

Put an amount of water into the tank, and open the exhaust air valve counterclockwise, start the motor, rotate the pressure regulator valve clockwise. When the water is sucked into the suction pipe and flows out of the return pipe, close the exhaust air valve and rotate the pressure regulator valve clockwise until the air is drained. When the pressure gauge reaches about 1500psi, check back-flow and leakage of the return pipe and other connectors.

If this phenomenon exists, press the “Pressure Relief Step” to relieve pressure first, then tighten the leaked part. If not, open the spray gun to perform the test and keep the pressure between 1000-1300psi.

Pressure Relief Procedure:

  1. Open the pressure regulator valve and exhaust air valve counterclockwise.
  2. Close the motor switch.

Note:

When opening the air exhaust valve, you should grasp the air exhaust valve hose firmly for avoiding falling off.

Airless Road Marking Machine
Airless Road Marking Machine

How to Maintain the Road Painting Machine?

  1. The sprayer should be cleaned immediately after finishing the spraying operation, which can remove any residual paint and prevent it from becoming hard. It also needs to change the paint into the corresponding solvent, and operate the machine until all paint in the machine is sprayed.
  2. It is necessary to clean the filter of the spray gun after using the road painting machine for a period of time. If the filter element is found to be damaged, the new filter element should be replaced.
  3. Spraying is not smooth during the spraying process, please check and clean the aspiration filter in time.
  4. Periodically check if the fasteners are loose, and the seals are leaking.
  5. Clean the oil inlet filter regularly, which can prevent foreign body plungers from causing abnormal wear of the plunger.
  6. Under normal conditions, it is necessary to check whether the hydraulic oil is clean and missing, after spraying for 400 hours. If hydraulic oil is clean but missing, add it; or if it is not clean, replace it. Replace the hydraulic oil, it needs to clean the oil chamber of the pump body with kerosene first, and then fill up the hydraulic oil.

The high-pressure airless sprayer of marking machine uses a high-pressure plunger pump to pressurize the paint to 3000PSK 210Kg/cm, and the high-pressure paint is delivered to the spray gun through a high-pressure hose, and the pressure is released through the nozzle to form a spray, thereby forming a dense coating on the wall surface. Because the paint does not require compressed air atomization, it is called airless spray.

The Road Marking Machine has the following advantages

  1. High efficiency:spraying efficiency is up to 200-500㎡/h, which is more 10 times than the drive roller.
  2. High quality: sprayed layer is smooth, dense, no brush marks, roll marks or particles.
  3. Long life for using:the high-pressure airless spray enables the paint particles to penetrate into the voids of the wall, so that the paint film and the wall surface form a mechanical bite, enhance the paint adhesion, and prolong the service life.
  4. It is easy to paintcorners, voids and uneven brushing areas.
  5. Save paint: the coating utilization rate is high, and it is easy to obtain a thickness of 30um coating for airless spraying, which can save 20-30% of the coating.

What should we do before the machine working?

  1. The paint to be sprayed must be filtered through a 60-mesh screen;
  2. Install the high-pressure hose, spray gun, nozzle, suction tube and so on.
  3. Check the connectionof every part in the high pressure system.

Test step before spraying

Put a amount of water into the tank and open the exhaust air valve with counterclockwise, start the motor, rotate the pressure regulator valve in clockwise. The water is sucked into the suction pipe and flow out of the return pipe, close the exhaust air valve and rotate the pressure regulator valve in clockwise until air is drained. When the pressure gauge reaches about 1500psi, check back-flow and leakage of the return pipe and other connectors.

If these phenomenon exists, press “Pressure Relief Step” to relieve pressure first, then tighten the leaked part. If not, open the spray gun to perform the test and keep the pressure between 1000-1300psi.

Pressure Relief Procedure:

  1. Open pressure regulator valveand exhaust air valve in counterclockwise.
  2. Close the motor switch.

Note: When opening the air exhaust valve, you should grasp the air exhaust valve hose firmly for avoiding falling off.

How to maintain the cold paint road marking machine?

  1. The sprayer should be cleaned immediately after finishing the spraying operation, which can remove any residual paint and prevent it becoming hard. It need to change the paint into the corresponding solvent, operate the machine until all paint in the machine is sprayed.
  2. It is necessary to clean the filter of the spray gunafter the spraying machine is used for a period of time. If the filter element is found to be damaged, the new filter element should be replaced.
  3. If spraying is not smooth during the spraying process, check and clean the aspiration filter in time.
  4. Periodically check if the fasteners are loose and if the seals are leaking.
  5. Clean the oil inlet filterregularly to prevent foreign body plungers from causing abnormal wear of the plunger.
  6. Under normal conditions, it is necessary to check whether the hydraulic oil is clean and missingafter spraying for 400hours. If hydraulic oil is clean but missing, add it; if the hydraulic oil is not clean, replace it. To replace the hydraulic oil, it is need to clean the oil chamber of the pump body with kerosene first, and then fill up the hydraulic oil.

    Please feel free to give your inquiry in the form below. We will reply in 24 hours.

    Product Model:

    Your Name(required):

    Your Email(required):

    Your Phone(required):

    Your country:

    Your Whatsapp(required):

    Your Message(required):